Follow us on Twitter

How to Install and Set Up the SkyBell HD Video Doorbell


IMG_2837_stomped

The SkyBell HD is a video doorbell that lets you see who’s at the door right from your smartphone and even talk to them without even opening your door. Here’s how to install the unit and set it up.

The SkyBell HD is similar to the Ring Doorbell, with one difference: the SkyBell unit must be hooked up to your existing doorbell’s wiring. The Ring Doorbell has the ability to do this, but it also has an internal battery that can power the whole unit itself. The SkyBell doesn’t have this, but installation is still pretty easy if you don’t have to reroute your doorbell wires.

Step One: Remove Your Existing Doorbell

In order to get to your doorbell’s wiring, you’ll need to first remove the doorbell button, which is usually mounted to the exterior wall of your house with two small screws that come right out with a screwdriver.

Once you have these screws out, you can pull out the doorbell button to expose more of the doorbell wires underneath. If you see two small wires, then the SkyBell is compatible. However, if your doorbell setup isn’t like this, then the SkyBell won’t be compatible. Don’t worry, though, as 99% of doorbells use two small wires.

Above: Most doorbell buttons will have two small wires connected to it.

Most doorbell buttons will have two small wires connected to it.

At this point, you can shut off the power to these wires by turning off the breaker that goes to the wires. However, in most cases, doorbell wiring is low voltage, and touching them won’t shock you or anything like that. However, if you want to be absolutely safe and/or are paranoid, there’s no harm in shutting off the breaker.

There will be two small wires connected to the back of the doorbell and they’ll be connected by small screws. Loosen these screws and remove the two wires from the doorbell button. At this point, your doorbell wires are ready to go.

Step Two: Install the SkyBell HD Unit

Grab the mounting plate that came with your SkyBell and hold it up to your exterior wall where you want the unit to be mounted, and mark with a pencil where the two mounting screws will be drilled.

IMG_3198_stomped

If the exterior of your house is brick or masonry, you’ll need to use the included drill bit to drill holes where you made marks, and then insert in the two yellow wall anchors before screwing on the mounting plate. If your exterior is wood, all you need to do is drill pilot holes using a drill bit that’s a tad smaller than the included screws.

IMG_3199_stomped

After that, screw in the mounting plate using the included screws. Be sure to feed the doorbell wires through the big hole in the center of the plate before mounting it.

IMG_3200_stomped

Take the two doorbell wires and wrap each one around its own screw on the left side, and then tighten the screws down. Make sure that the two wires aren’t touching each other. It also doesn’t matter which wire goes to which screw, because the button will simply close the circuit between the two wires to make your doorbell chime go off.

IMG_3203_stomped

Next, grab the SkyBell HD unit and begin placing it over the mounting plate. Start by placing the tab at the top of the unit inside the slot on the mounting plate.

IMG_3204_stomped

After that, press down the rest of the unit onto the mounting plate. Then, use a screwdriver to drive in the screw on the bottom of the unit to lock it in place.

IMG_3205_stomped

Once the SkyBell is mounted, it will automatically boot up and will alternate between red and green lights.

IMG_3206_stomped

Step Three: Download and Set Up the SkyBell App

Go to the App Store on your iOS device or the Play Store on your Android device and download the SkyBell HD app (iOS, Android).

IMG_3196_stomped

Once it’s installed, open it up and tap on “Sign Up”.

IMG_3207_stomped

Enter in your email address, create a password, and type in your name. Then tap on “Sign up”.

IMG_3208_stomped

On the next screen, tap on “Add a new SkyBell”.

IMG_3209_stomped

Tap on “OK let’s begin” at the bottom.

IMG_3210_stomped

Make sure that your SkyBell unit is flashing green and red. If not follow the instructions on the screen. If everything looks good, tap on “Next” at the bottom.

IMG_3211_stomped

After that, if you’re on an iOS device, close out of the app temporarily and open up the Settings app and select “Wi-Fi”. If you’re on an Android device, you’ll simply select your home’s Wi-Fi network, which is detailed a couple of steps later on.

IMG_3214_stomped

Tap on the SkyBell HD Wi-Fi SSID in the list to connect to it.

IMG_3215_stomped

Once connected, go back into the SkyBell app. Select your home’s Wi-Fi network and then tap on “Next” at the bottom.

IMG_3218_stomped

On the next screen, enter in the password for your Wi-Fi network and tap on “Go” or “Next”.

IMG_3219_stomped

Your SkyBell HD will spend a few moments to configure and connect to your home’s Wi-Fi network.

IMG_3220_stomped

Once complete, tap on “Go to my SkyBell” at the bottom of the screen.

IMG_3221_stomped

You’ll be taken to the main screen of the app, where you can see a live view of the camera, as well as view recent activity of your doorbell. It might be blank at first, but once you get some activity going, the main screen will begin to populate. You can also tap on the gear icon in the top-right corner to access the settings.

IMG_3222_stomped

Craig Lloyd is TIME Magazine’s 2006 Person of the Year, as well as a mediocre gamer, aviation geek, baseball fan, and an introvert to the max. He began his career as a young, naive teenager tinkering around with the family computer and has since blossomed into the beautiful geek that he is today.


How to Enable the Apple TV’s Dark Mode
How to Turn an Old Smartphone Into a Dash Cam for Your Car

Comments

comments